Lifehacks

Guide to Installing a Direct Water Heater

GREEN Dien May is here to help make your bathroom the most beautiful it can be. Installing a direct water heater is not complicated, but there are a few steps you need to follow to ensure safety and that it will run smoothly. We walk you through the steps to installing one for your convenience.

Administrator

31 July, 2023

317

New Computer Installation Tools Available

Please gather the necessary tools and supplies for installing a direct water heater.

Water Heater Accessories Available with Purchase

The complete machine and accompanying accessories are included with the purchase.

2. Preparation of materials for machine installation (Dien May GREEN offers support for customer preparation)

Instructions for prepping the machine:

Water supply cable
Single-phase electrical circuit breakers – 20A or 30A.
Daphaco electric wire

Daphaco electric wire
We need to purchase additional flexible hoses in order to properly fill water into the machine.
To perform the installation, you will need a set of essential tools, including a pencil, electric tester, screwdriver, ruler, wrench, wire cutter, and drill. These tools will enable you to efficiently and effectively complete the installation process.

How to Combat Climate Change: A Guide

Step 1: Begin by using a screwdriver to carefully remove the mask or cover of the water heater.

Remove the cover of the water heater

To remove the front panel of the water heater, please use a screwdriver. Ensure that you select the appropriate type of screwdriver to avoid any damage to the unit. Carefully remove the screws before taking off the front panel.

The water heater has been removed from the mask

Step 2: Mount the machine onto the wall, ensuring it is positioned accurately with the aid of a ruler. Employ a pencil to mark both the hanger and the holes located along the rear of the machine.

Position the machine precisely using a ruler, and mark it accurately with a pencil

Moving the machine out of position, begin drilling holes. Close the stopper and then carefully align the machine’s available holes with the position of the stopper. Securely fasten the screws in place.

Securely attach the machine to the wall

Step 3: Find the installation location for the shower faucet and CB. Choose the appropriate position and mark the hole with a pencil using the holes on the slider. Then, secure the slider in place on the wall and use the screw to complete the accessory installation.

Determine the location of the shower faucet and control box.

Please mount the circuit breaker on the wall.

Mount the circuit breaker on the wall

Please follow the steps below to install the shower on the wall:

1. Begin by gathering all the necessary tools and materials for the installation.

2. Choose the desired location on the wall for the shower installation. It should be at a convenient height and within reach of the plumbing connections.

3. Mark the location on the wall using a pencil or marker. Use a level to ensure that the marks are aligned and straight.

4. If needed, drill holes into the wall at the marked locations to accommodate any mounting brackets or screws. Make sure to use the appropriate size drill bit for your specific wall material.

5. Attach any mounting brackets or screws to the wall, following the manufacturer’s instructions. These will provide support for the shower and ensure it stays securely in place.

6. Next, connect the shower plumbing to the existing water supply lines. This may involve cutting into existing pipes and attaching connectors or fittings.

7. Once the plumbing connections are secure, position the shower onto the mounting brackets or screws. Make sure it is level and tightly secured.

8. Finally, test the shower to ensure it is functioning properly. Turn on the water supply and check for any leaks or issues. If everything looks good, you can now enjoy your newly installed shower!

Please note that if you are not confident in your ability to install the shower yourself, it is always recommended to hire a professional plumber for the job. They have the necessary knowledge and expertise to ensure a proper and safe installation.

Securely mount the shower unit onto the wall

Please secure the faucet fixing screw.

Secure the showerhead fixing screw

Step 4:

Next, we will install the 3-in-1 valve and the water inlet on the right side of the machine. Using a wrench, carefully tighten the valve in place. Then, remove the warning stickers from the top of the valve, being careful not to drop the loose mesh or the rubber gasket that is situated at the top of the valve.

Ensure that the loose mesh rubber gasket is not dropped at the valve head

Please install the 3-in-1 valve and water inlet on the right side of the machine.

Attach the 3-in-1 valve and remove the sticker

Please connect the valve end to the water line and the other end to the water supply line. Use moderate force when twisting to prevent damage to the connector.

Use a plastic pipe to connect the 3-in-1 valve to the water supply valve

Please connect the shower arm to the water outlet located on the front left side of the water heater.

Connect the hand shower to the water outlet

Step 5: Plug in the power cord to the machine.

Please ensure proper and secure installation of the phase wire, neutral wire, and ground wire into the contacts of the machine. It is crucial that the wires are connected correctly to ensure optimal functionality.

Connect the wire to the contact

Connect the machine to the previously mounted circuit breaker box.

Connect the machine to the previously mounted circuit board (CB)

To complete the installation process, carefully affix the front panel onto the machine, making sure to use the appropriate screws that were initially removed. Prior to attachment, remove the scratch-resistant screen from the front panel and subsequently insert the adjustment buttons. It is imperative to ensure that the adjustment buttons fit seamlessly into their designated positions.

Proceed with the installation of the machine’s front and insertion of the control knob

The installation of the water heater has been successfully completed.

Water heater installation successfully completed

Step 6:

Ensure proper grounding of the machine to prevent electric leakage and minimize potential risks for users.

Verifying Machine Performance and Providing Guidance to Users

Step 1: Verify the functionality of the ELCB anti-shock circuit breaker and other machine functions.

Check the functionality of the ELCB anti-shock circuit breaker on the machine.

Step 2: Provide a demonstration on using the machine’s function buttons, instructing customers on proper usage.

Guide customers in utilizing the functionality buttons of the machine

The direct water heater installation has been successfully finished.

Thank you for taking the time to read our article on installing a water heater. We hope you found it informative and helpful. If you have any questions or comments, please leave them in the space provided below. We appreciate your feedback and look forward to hearing from you.

Ariston IM-4522EP Water Heater 4.5kW

Ariston IM-4522EP water heater is a top-of-the-line product designed to provide efficient and reliable hot water supply for your home or business. With a power output of 4.5kW, this water heater can heat a large amount of water quickly and efficiently.

One of the key features of the Ariston IM-4522EP water heater is its energy-saving capabilities. It uses advanced heating technology and insulation to minimize heat loss, resulting in lower energy consumption and reduced costs. This makes it a cost-effective choice for both residential and commercial use.

The Ariston IM-4522EP water heater is also equipped with safety features to ensure worry-free operation. It has a temperature and pressure relief valve to prevent over-heating and pressure build-up, as well as a thermal cut-off to protect against overheating. This makes it a safe and reliable option for your hot water needs.

Another advantage of the Ariston IM-4522EP water heater is its compact size and sleek design. It can be easily installed in any space, whether it’s a small apartment or a large office building. Its modern and stylish look also adds a touch of elegance to any interior.

In conclusion, the Ariston IM-4522EP water heater is a high-quality and efficient solution for your hot water needs. With its energy-saving features, safety precautions, and attractive design, it offers both functionality and style. Invest in the Ariston IM-4522EP water heater and enjoy a reliable supply of hot water for years to come.